The 2014 Jeep Grand Cherokee 3.6 V6 offers a blend of capability and comfort, and understanding its oil capacity helps keep the powertrain running smoothly. Using the right amount and type of motor oil is essential for optimal performance, longevity, and warranty compliance.
This guide focuses specifically on the 2014 Jeep Grand Cherokee 3.6 L V6, providing detailed specifications, change procedures, and practical tips you can apply right away.
| Year | Engine | Oil Capacity | Oil Filter |
|---|---|---|---|
| 2014 | 3.6 L V6 (68RFE automatic) | 5.1 quarts with filter | OEM or equivalent Fram, WIX |
| 2014 | 3.6 L V6 (filter location) | Approx. 4.5 quarts new oil | Drain plug: 15 mm hex |
| 2014 | Recommended oil | 0W-20 synthetic blend or better | Torque spec: 20–25 ft-lbs |
Oil Fill Procedure for the 3.6 L V6
Preparing the Vehicle
Park the 2014 Grand Cherokee on level ground, set the parking brake, and turn off the engine. Raise the front safely with a jack and support it with jack stands if you need under-vehicle access, or use ramps if preferred. Gather the correct 0W-20 synthetic oil, a new OEM-style filter, a 15 mm wrench, an oil filter wrench, a drain pan, and a funnel before starting.
Draining and Refilling
Locate the oil drain plug underneath the oil pan, position the drain pan, open the drain plug carefully, and let the oil drain completely. Remove the oil filter, prep the new gasket with fresh oil, install the new filter hand-tight, then replace the drain plug securely. For the 2014 3.6 L V6, add about 4.5 quarts of fresh 0W-20, but always verify with the dipstick after initial fill to reach the proper level.
Recommended Oil Specifications
Viscosity and Type
Chrysler specifies 0W-20 mineral or synthetic blend for most 2014 Grand Cherokee 3.6 L applications, although many owners prefer a full synthetic for better temperature stability and protection. Using 5W-20 is also acceptable in a wide range of temperatures, but confirm on the oil filler cap or in the owner’s manual. Exceeding the factory viscosity can affect fuel economy, cold-start protection, and warranty coverage.
Capacity and Filter Details
The oil system capacity for the 2014 3.6 L V6 is approximately 5.1 quarts when including the oil filter. During a filter change, you will typically add around 4.5 quarts to refill the engine, but the exact amount can vary slightly depending on the filter design and remaining oil in the cooler lines. Always follow the capacities listed on the oil filler cap or in the vehicle-specific guide to avoid overfilling, which can increase pressure and lead to leaks.
Maintenance Schedule and Intervals
Factory Recommendations
Jeep suggests oil and filter changes every 12 months or 7,500 miles for normal driving, using the 0W-20 specification. If you frequently tow, drive in stop-and-go traffic, operate in extreme temperatures, or make short trips, consider a more conservative schedule around 5,000 miles or 6 months. Keeping up with these intervals helps maintain the 3.6 L V6’s efficiency, power, and long-term reliability.
Signs It Is Time for a Change
Watch for signs like a low oil level warning, unusual engine noise, reduced fuel economy, or a burning smell from the engine bay. Dark, gritty oil on the dipstick indicates contamination and the need for a change. Checking the oil regularly, especially on the 2014 Grand Cherokee with its 3.6 L V6, allows you to catch issues early and prevent excessive wear on critical components.
Key Takeaways for the 2014 Grand Cherokee 3.6 L
- Oil capacity is about 5.1 quarts including the filter.
- Recommended oil is 0W-20 synthetic or synthetic blend.
- Use a 15 mm drain plug and a compatible oil filter.
- Adhere to the 7,500-mile or 12-month change interval under normal driving.
- Check the oil level regularly and address leaks or contamination promptly.
FAQ
Reader questions
How much oil does a 2014 Jeep Grand Cherokee 3.6 V6 hold with the filter?
The total oil capacity is approximately 5.1 quarts when including the oil filter, with about 4.5 quarts needed to refill the engine after a filter change.
Can I use 5W-20 instead of 0W-20 in my 2014 Grand Cherokee 3.6 L?
Yes, 5W-20 is acceptable and works well in most climates, but check the oil filler cap or owner’s manual; many owners prefer 0W-20 synthetic for improved cold-start protection and fuel efficiency.
What type of oil filter is best for the 3.6 L V6?
Use an OEM-style or high-quality aftermarket filter from brands such as Fram or WIX that matches the original equipment specs; ensure the gasket is pre-lubricated before installation.
How often should I change the oil on my 2014 Grand Cherokee 3.6 L?
Follow the factory schedule of every 12 months or 7,500 miles for normal use, or every 6 months or 5,000 miles if you drive in severe conditions to protect the engine and maintain warranty coverage.