Owners of a 2014 Jeep Cherokee often wonder how much oil does a 2014 jeep cherokee take during routine maintenance. Knowing the correct capacity helps protect the engine and supports long term reliability for daily driving.
Using the proper amount and type of oil keeps the powertrain running smoothly and can prevent expensive repairs down the road. The following sections break down the exact specifications, procedures, and related details for this model year.
| Specification | Value | Notes |
|---|---|---|
| Engine | 2.4 L Tigershark I4 | Base engine on many 2014 Cherokee models |
| Oil Capacity (with filter) | 4.4 quarts (approx.) | Typical figure for the base engine |
| Recommended Oil Type | 5W-20 synthetic blend or full synthetic | Check the owner’s manual for exact viscosity |
| Oil Filter Part | Motorcraft FL-820-S or equivalent | OEM or quality aftermarket option |
| Drain Plug Torque | 18–22 lb-ft | Follow factory procedure for sealing |
2014 Jeep Cherokee 2.4L Engine Oil Requirements
The 2014 Jeep Cherokee commonly comes with a 2.4L Tigershark naturally aspirated engine designed for a balance of efficiency and performance. For this four cylinder powerplant, manufacturers specify a fill capacity of roughly 4.4 quarts when including the new filter.
Always confirm the exact number for your particular build by reviewing the printed maintenance section in the owner’s manual or the sticker inside the driver door jamb. These sources account for potential changes in trim and accessory configurations that may slightly alter the volume needed.
Using a full synthetic or a high quality synthetic blend rated 5W-20 helps protect the bearings and camshafts while supporting the turbocharged variants that some models may include. Clean debris and the correct filter further ensure that the system stays within the designed operating range.
How to Check and Add Oil in Your 2014 Cherokee
Proper level checking is essential when learning how much oil does a 2014 jeep cherokee take during a top up. Start with the vehicle on level ground, switch off the engine, and wait a few minutes so the oil settles into the pan for an accurate dipstick reading.
Locate the dipstick, pull it clean, wipe it, reinsert it fully, and then check the mark between the minimum and maximum indicators. Add small amounts gradually to avoid overfilling, which can increase pressure in the crankcase and damage seals.
After reaching the correct level, run the engine for a short period, then turn it off and recheck. This double check ensures that the filter has filled and that no hidden low spots remain, giving you confidence in the final capacity.
Choosing the Right Oil and Filter
Selecting the right oil for your 2014 Cherokee goes beyond just answering how much oil does a 2014 jeep cherokee take. The viscosity and certification labels on the container must match factory recommendations for year round protection.
A premium synthetic meets demanding API and ILSAC standards, offers better flow in cold weather, and maintains stability at higher temperatures encountered during towing or extended highway driving.
Replace the oil filter at every oil change, and use a reputable brand that meets or exceeds OEM specifications. A quality gasket and proper seating prevent leaks and ensure that the new filter saturates quickly for optimal filtration.
Maintenance Tips and Best Practices
Staying consistent with change intervals helps maintain the correct performance and longevity of the engine. Many drivers find it useful to track mileage or time in a simple log, noting when each service was completed.
- Use the exact oil capacity specified for your engine, typically around 4.4 quarts with filter for the 2.4L
- Stick to the recommended 5W-20 viscosity unless a different grade is specified for special conditions
- Replace the oil filter with each change and torque the drain plug to factory specs
- Check the dipstick after refilling to confirm the level without overfilling
- Consult the owner’s manual for model year nuances and extended drain intervals if using a approved synthetic
Final Recommendations for Your 2014 Cherokee
Following the factory guidance on oil type, capacity, and change intervals keeps your Cherokee running strong and supports resale value. Consistent attention to the dipstick, filter selection, and torque procedures completes a reliable maintenance routine.
FAQ
Reader questions
How many quarts should I add if I am changing the oil myself on my 2014 Cherokee? Plan for about 4.4 quarts including the filter, but verify with the dipstick during filling to avoid overfilling. Can I use 5W-30 instead of 5W-20 in my 2014 Jeep Cherokee?
It is best to follow the factory recommended 5W-20 viscosity, as 5W-30 may affect performance, efficiency, and warranty coverage in some cases.
Does the oil capacity change if my Cherokee has a V6 engine?
Some variants may have different displacement; always check the specific engine code and refer to the maintenance guide for the exact oil capacity.
What should I do if I accidentally overfill the oil after asking how much oil does a 2014 jeep cherokee take?
Drain the excess oil to the proper level, because overfilling can create excessive pressure, cause leaks, or lead to increased engine wear.